Passenger European Leakage Cable Detector Installation Specifications and Common Troubleshooting Methods

As a perimeter security product, leaking cable detectors are also widely used in life. So what should we pay attention to when installing, how can we make the leaking cable work better? Start with the requirements when installing a leaky cable detector!

Shanghai Keou Security - Leakage Cable Detector System Diagram - Perimeter Alarm Series

The first is the requirement for the length of the perimeter defense zone.

The leakage zone of the passenger-European security cable detector needs to be installed more than 100m. Cables smaller than 100m can be customized, but the main unit does not need to be changed.

The front end of the leaky cable detector consists of a 5m long non-leakage cable and a leaky cable. The leak is freely cut according to the length of the zone. The standard factory length is 200m.

Second is the requirement for "installation environment"

Leakage cable detector main unit should be placed in a waterproof protection box to avoid high frequency interference sources near the main unit and power line. And the adjacent zones should use hosts of different frequencies, and the corresponding installation environment is also strictly controlled.

1, the host installation environment temperature: -10 Â° C ~ +50 Â° C

2, distance from the sidewalk: more than 2m, more than 5M away from the carriageway

3. Distance from trees: Trees with a diameter of 20cm or more are kept above 50cm

4, from the metal fence or well cover: 50cm or more

5, distance from the river: more than 1m

These conditions are intended to prevent pedestrians and other factors from affecting the detector. If the protected area does not meet the above installation conditions, it is not recommended to install a leaky cable detector. Unless some places can be disarmed during work hours, the installation guards during the off-duty period.

Finally, the requirements for "cable laying".

Cable installation spacing

0.6~~1.2 meters (recommended 0.8 meters)

Cable burying depth

Cement floor 3cm~8cm (recommended 5cm)

Loose soil: 5cm~-10cm

When the cable is buried through trees, shovel, etc., the depth of burial should be appropriate;

When the cable turns, the flat root line turns in parallel, the cable is not hard folded, and the bending radius is not less than 20cm;

The two non-leakage cables should not be crossed and closely attached to each other. The excess should be cut off, re-installed, and not coiled in a waterproof box or underground line.

When multiple sets of leaky cables are used, the standard usage is that two adjacent sets of leaking cables are connected end to end. Due to the transition zone at the beginning of the leaking cable, in order to ensure reliable detection of the adjacent two detector joints, it is recommended that the operating frequencies of the two sets of ends are not the same, and the same frequency cannot overlap (Note: Before installation, pay attention to the leaky cable host) A, B two frequencies)

The leaked cable after installation may have some minor problems during the test. At this time, some common fault solutions are needed. The overall summary is as follows:

Shanghai Keou Security - Leakage Cable Detector System Diagram - Perimeter Alarm Detector Products

Hollow Anchor Bar

Hollow anchor bar means a rod that transfers the structures or geotechnical load to a stable rock formations, anchor bolt consists of rod, drill bit, coupling, plate, grouting stopper and nut. Widely used as an efficient anchoring means, in tunnel pre-support, slope, coast, mine, water conservancy projects, building foundation, roadbed reinforcement and geological diseases treatment such as landslip, crack, sink age. It`s irreplaceable in narrow construction environment. Hollow anchor bar is made of seamless tube with high strength.

Advantages and Characteristics :

1.No casings required, because anchor bars can be drilled into loose soils without needing casings to support the boreholes.

2.Fast drilling and installation, because drilling, installation and grouting are in a single operation.

3.Both rope threads and trapezoid threads are robust and ideal for rotary-percussive drilling and ensuring a high level of bond with the borehole gout.

4.The hollow core not only serves for flushing during drilling, but also for grouting after drilling.

5.Continuous threads ensure the bars can be cut and coupled at any point, or extended.

6.Different anchor bits are available for different ground conditions.

7.Duplex anti-crossin process, hot-dip galvanized and epoxy coating system.

Anchor Bolt,Anchor Rod,Hollow Anchor Bars,Hollow Grab Bar Anchor

Tianjin Youfa Steel Co., Ltd , https://www.youfametal.com